Search results for 'red'

Items 1 to 10 of 42 total

per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5

Set Ascending Direction
  1. CMS Mould Release W

    CMS Mould Release W

    A fast drying solvent based liquid release agent for foundry patterns and core boxes used for the production of moulds and cores in cold setting chemical sands.


    Learn More...
  2. Trueline Dowels

    Trueline Dowels

    True-Line Steel Dowels are broached and flange-slotted which means that:
    * They can be inserted easily, accurately and quickly.
    * Because of the slotted flange, the Bushing and Pin can be removed with wrenches that are either flange-slotted or broached, even if the Pin is broken.
    * Tapered shaft design of Pin and square shoulders contribute to accurate alignment.
     


    Learn More...
  3. Ebalta OH11 Steel

    Ebalta OH11 Steel

    Ebalta OH 11 steel   is a two component polyurethane gel- coat.
    OH 11 steel consists of polyols and additives including fine steel  poweder,  which when cured  results  in  a  hard  tough surface that is wear and heat resistant.

    OH 11 steel is especially formulated for the facing of press tools backed with GM 921 and steel granules.
     


    Learn More...
  4. CMS Stop Coat

    CMS Stop Coat

    A light reddish-brown water based ceramic coating used for the prevention of carburisation or decarburisation of steel during the Heat Treatment process. It can be used with or without atmospheres, with pack hardening or carburising materials.


    Learn More...
  5. Samplers

    Samplers

    A wide range of application tailored samplers for various types of molten metals complete the Heraeus Electro-Nite scope of supply. Simple to apply, easy to strip and representative for the melt, these are the characteristics of a good sampler. For ultra-clean sampling from steel melts we offer a special pneumatic sampling system. This and combined to a design for rapid preparation and suited for automatic handling make our samplers preferred choice.


    Learn More...
  6. Nozzles

    Nozzles

    The CMS Nozzle is a high quality cast refractory nozzle used in bottom pouring applications for ferrous castings.

    CMS Nozzles are a reverse tapered design, manufactured in three profiles, series A, series B and series D. Bore sizes range from 25 mm to 100 mm.

    CMS Nozzles can be changed hot or cold from underneath the ladle, permitting the same ladle to be used a number of times throughout the day.

    The selection of nozzle refractory depends on the actual service conditions.
     


    Learn More...
  7. Furan

    Furan

    Introduction
    SQG series No Bake Furan Resin is a kind of environmentally friendly foundry binder.

    Different types of resins can be used for steel casting, iron casting and non-ferrous casting. They appear pale yellow to red brown transparent liquid with the following characteristics:

    •    Low viscosity increases the speed of resin addition and the fluidity of moulding sand.

    •    Low free Formaldehyde content and less odour. This improves working condition and lightens environmental pollution.

    •    High strength reduces resin addition ratio, which means lower cost and higher quality of castings.

    •    Good collapsibility, high precision of casting with clear-cut and clean surface reduces the workload for cleaning and improves work efficiency.
     


    Learn More...
  8. Coil Grout

    Coil Grout

    A conventional, hydraulically bonded grouting castable of the high alumina class with good strength and dimensional stability.


    Learn More...
  9. Plate Vibrator

    Plate Vibrator

    The Cleveland Vibrator Co. LA Series of pneumatic industrial vibrators are designed specifically for optimizing match-plate operations, improving quality and reducing cost in the Foundry.
     
    DURABLE - one-piece, ductile iron housing and spring-less design ensure long effective life and minimal down time.
     
    VERSATILE - range of vibration intensities and swiveling air intake ensure a good fit for your specific match-plate operation
     
    EASY - comes with mounting fasteners for quick set-up
     


    Learn More...
  10. Mudding Compound

    Mudding Compound

    DESCRIPTION:

    A grey-black water based refractory sealing compound designed for general repairs to foundry cores and moulds.

    CMS MUDDING COMPOUND contains high purity graphite. It is supplied in a ready-to-use paste form, with excellent filling and sleeking properties suitable for all organic and inorganic bonded sands.

    PHYSICAL PROPERTIES:

    Colour                  : Grey-black
    Physical Form      : Thick paste
    Specific Gravity    : 1.50 - 1.70 Kg / Ltr
     


    Learn More...

Items 1 to 10 of 42 total

per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5

Set Ascending Direction