Search results for 'Search our website here.'

Items 1 to 10 of 39 total

per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4

Set Ascending Direction
  1. CMS Mould Release W

    CMS Mould Release W

    A fast drying solvent based liquid release agent for foundry patterns and core boxes used for the production of moulds and cores in cold setting chemical sands.


    Learn More...
  2. SG130 Pouring Caps

    SG130 Pouring Caps

    Pouring caps for either SG130 or SG130L.


    Learn More...
  3. Zircon Flour

    Zircon Flour

    325 mesh Zircon Flour.


    Learn More...
  4. Thermal Analysis - Cast Iron

    Thermal Analysis - Cast Iron

    Tracing and analyzing the temperature of a cooling and solidifying iron sample is named Thermal Analysis. The plateaus of liquidus and solidus temperatures of the cooling iron sample in a cup allow the calculation of carbon equivalent, carbon and silicon. Relevant formulas in our instruments may be used to calculate physical properties of the iron casting.

    Our range of QuiK-Cup cups (QuiK stands for Quartz insulated type K thermocouple) are designed for various types of cast iron, unalloyed, alloyed, solidifying grey or white and taken from Cupola through runner, furnace or tundish.

    Sensor: QuiK-Cup 


    Learn More...
  5. Oxygen Control

    Oxygen Control

    Monitoring oxygen activity throughout the steel making process is essential for production control and final as-cast quality. In less than 10 seconds, our expendable oxygen sensors measure the melt's oxygen activity a(O) over a wide concentration range in areas from hot metal desulphurization, furnace tapping, through ladle refining and continuous casting. Correlations to S and Si in Hot Metal, carbon and aluminium in primary and secondary steelmaking are implemented in the formulas of our instruments.


    Learn More...
  6. Samplers

    Samplers

    A wide range of application tailored samplers for various types of molten metals complete the Heraeus Electro-Nite scope of supply. Simple to apply, easy to strip and representative for the melt, these are the characteristics of a good sampler. For ultra-clean sampling from steel melts we offer a special pneumatic sampling system. This and combined to a design for rapid preparation and suited for automatic handling make our samplers preferred choice.


    Learn More...
  7. Stopper Rod Sleeves

    Stopper Rod Sleeves

    Stopper Rod Sleeves for bottom pouring ladles.

    A range of sizes are available on request.


    Learn More...
  8. Nozzles

    Nozzles

    The CMS Nozzle is a high quality cast refractory nozzle used in bottom pouring applications for ferrous castings.

    CMS Nozzles are a reverse tapered design, manufactured in three profiles, series A, series B and series D. Bore sizes range from 25 mm to 100 mm.

    CMS Nozzles can be changed hot or cold from underneath the ladle, permitting the same ladle to be used a number of times throughout the day.

    The selection of nozzle refractory depends on the actual service conditions.
     


    Learn More...
  9. Furan

    Furan

    Introduction
    SQG series No Bake Furan Resin is a kind of environmentally friendly foundry binder.

    Different types of resins can be used for steel casting, iron casting and non-ferrous casting. They appear pale yellow to red brown transparent liquid with the following characteristics:

    •    Low viscosity increases the speed of resin addition and the fluidity of moulding sand.

    •    Low free Formaldehyde content and less odour. This improves working condition and lightens environmental pollution.

    •    High strength reduces resin addition ratio, which means lower cost and higher quality of castings.

    •    Good collapsibility, high precision of casting with clear-cut and clean surface reduces the workload for cleaning and improves work efficiency.
     


    Learn More...
  10. Styrotherm Insulating Tiles

    Styrotherm Insulating Tiles

    Lightweight insulation tile used for large feeders and other high temperature insulation applications.

    Styrotherm-G riser lining tiles do not evolve any gas during casting and because of the low density of approximately 0.6 g/cm3 cause an extension factor of solidification of 2.2. This corresponds to a modulus extension factor of 1.45

    The tiles are pale yellow in colour, have a trapezoidal profile section, and are machined for improves flatness and accuracy.
     


    Learn More...

Items 1 to 10 of 39 total

per page
Page:
  1. 1
  2. 2
  3. 3
  4. 4

Set Ascending Direction